Join our mailing list!
You are here: Home > USED MOLDING MACHINES > Used NISSEI Machines > NISSEI Up to 200tons
Small Tonnage Late Model Nissei Machines
 

All used machines listed on our website are owned solely by En-plas Inc.


We are not marketing or selling other dealer's equipment!

 
 
Please click here to sign up for our used machine and robot updates!
 
Questions?  Would you like more info or a quotation?  Please contact us for more details!
 
140ton Nissei FN3000 (2001)
New Arrival!

    Used FN3000 Nissei 150ton 
 

Used Year 2001 En-Plas Nissei Model FN3000-36A Injection Molding Machine

With NC9300T Controller, tested
 

SPECIFICATIONS

CLAMP UNIT

Clamp force:                                                        154 U.S. Tons

Distance Between Tie Bars (HxV):                     18.9" x 18.9"

Platen size (HxV):                                               27.6" x 27.6"

Maximum clamp stroke:                                      23.6"

Mould shutheight:                                               9.8"

Maximum daylight:                                             33.5"

Hydraulic ejector stroke:                                     3.5"

 

INJECTION UNIT

Screw diameter:                                                   56mm (2.2")

Shot size:                                                             14.84 oz. G.P.P.S. (C)

Injection Pressure:                                               19410 PSI

Screw speed:                                                        0-200 RPM high torque

200-240 RPM low torque

 

ELECTRICAL UNIT

Pump motor:                                                        40 HP

Primary voltage/phase/cycle:                               575/3/60

Heater voltage/phase/cycle:                                 230/3/60

Control circuit:                                                     24 volt DC

 

NOTE:  Heater voltage requires separate 230 volt supply

 

GENERAL

Hydraulic oil quantity requirements:        515 litres

 *Oil can be supplied by En-Plas for an additional charge

 

MACHINE EQUIPPED WITH USED :

      1.  Dual core pull

      2.   Cycle counter

      3.   Centralized manual lubrication system

      4.   Screw cold start preventing circuit

      5.   Hydraulic oil temperature upper and lower limit warnings

      6.   Used mounting pads

       7.  Hopper magnet

      8.   Air blow off circuit

      9.   Air core pull

    10.   Hardened Barrel & Screw

 
140ton Nissei FN3000 (1998)
NEW ARRIVAL 
Nissei FN3000 (150ton)
 

ONLY USED YEAR 1998 NISSEI MODEL FN3000/140-36A INJECTION MOULDING MACHINE WITH

 9000F Controller 

 

SPECIFICATIONS

 

CLAMP UNIT

Mold clamping force:                                             154 U.S. Tons

Mold clamping stroke                                            600 mm (23.62”)

Minimum mold thickness                                        250 mm (9.84”)

Maximum daylight opening                                     850 mm (33.46”)

Clearance between tie bars (HxV)                         480 mm x 480 mm (18.90” x 18.90”)

Die plate dimensions (HxV)                                   700 mm x 700 mm (27.56” x 27.56”)

Ejector stroke                                                           90 mm (3.54”)

 
INJECTION UNIT

Shot size:                                                               14.83 oz. G.P.P.S. (C)

Injection Pressure:                                                 19410 PSI

Screw diameter:                                                    2.2" (56mm)

Screw speed:                                                        0-200 RPM Constant torque

200-240 RPM Variable torque

 
ELECTRICAL UNIT

 

Pump motor kW:                                                   30

Primary voltage/phase/cycle:                                  575/3/60

Heater voltage/phase/cycle:                                    230/3/60

Control circuit:                                                       24 volt DC

 

NOTE:  Heater voltage requires separate 230 volt supply

*Transformer can be supplied by En-Plas for an additional charge

 

GENERAL

 

Hydraulic oil quantity requirements:        515 litres

*Oil can be supplied by En-Plas for an additional charge

 

 
Questions?  Would you like more info or a quotation?  Please contact usfor more details!
 
 
180ton Nissei FN4000 (Yr 2000)
 
Nissei FN4000 equipped with a special hydraulic mold clamping system and a 9300T controller  Equipped with a American Aerostar hydraulic mold clamping system - can be removed - does not include powerpack system
 
ONE YR 2000 NISSEI FN4000 INJECTION MOLDING MACHINE WITH 9300T Controller

SPECIFICATIONS

 

CLAMP UNIT

Mold clamping force:                                             196 U.S. Tons

Mold clamping stroke                                            700 mm (27.56”)

Minimum mold thickness                                        250 mm (9.84”)

Maximum daylight opening                                     950 mm (37.40”)

Clearance between tie bars (HxV)                         530 mm x 530 mm (20.87” x 20.87”)

Die plate dimensions (HxV)                                   770 mm x 770 mm (30.31” x 30.31”)

Ejector stroke                                                       110 mm (4.33”)

 

INJECTION UNIT

Screw diameter:                                                    22mm

Shot size:                                                               30grams

 
 
 
Questions?  Would you like more info or a quotation?  Please contact us for more details!
 
TACT Controller             9300T Controller                 9000F Controller

Nissei's Latest TACT Controller       Nissei's Full Color Touch Screen 9300T Controller       Nissei's 9000F Controller
 
Used Equipment may have had modifications made to them that En-Plas Inc. is unaware of and take no responsibility for.
Specifications listed on our used equipment pages may differ from actual specifications on the equipment and are meant solely as a guideline.