|
Small Tonnage Late Model Nissei Machines
60ton Nissei PS60
new arrival
photo and specs to come
80ton Nissei FN1000 (1998)
TWO ONLY 1998 NISSEI MODEL FN1000 INJECTION MOULDING MACHINES, BOTH COMPLETE WITH 9300T Controller
SPECIFICATIONS
CLAMP UNIT
Clamp force: 88 U.S. Tons
Clamping stroke 470 mm
Minimum mold thickness 200 mm
Maximum daylight opening 670 mm
Tie Bar clearance (HxV): 385 mm x 385 mm
Die plate dimension 545 mm x 545 mm
Ejector stroke 75 mm (2.76)
INJECTION UNIT
Screw diameter 19 mm
Shot size: 15grams
80ton Nissei FS8012ASE (1991)
new arrival
photo to come
(1) ONLY NISSEI MODEL FS80S12ASE INJECTION MOULDING MACHINE
SPECIFICATIONS
CLAMP UNIT
Clamp force: 88 U.S. Tons
Distance Between Tie Bars (HxV): 14.8" x 14.8"
Platen size (HxV): 21.1" x 21.1"
Maximum clamp stroke: 13.8"
Mould shutheight: 6.3" to 13.2"
Maximum daylight: 27"
Hydraulic ejector stroke: 3"
INJECTION UNIT
Shot size: 5.3 oz. G.P.P.S. (C)
Injection Pressure: 21045 PSI
Screw diameter: 1.57"
Screw speed: 0-140 RPM (low torque)
0-175 RPM (high torque)
ELECTRICAL UNIT
Pump motor: 15 HP
Primary voltage /phase/cycle: 575/3/60
Heater voltage/phase/cycle: 230/3/60
Control circuit: 24 volt DC
NOTE: Heater voltage requires separate 230 volt supply
GENERAL
Machine weight: 4 U.S. Tons Hydraulic oil quantity requirement: 85 gallons
120ton Nissei DC120 Double Injection machine
2 Available - Both 2004 Models with almost zero hours!!
Two (like new) ONLY YEAR 2004 EN-PLAS NISSEI MODEL DC120-9A HYDRAULIC TYPE
DOUBLE INJECTION MOULDING MACHINES WITH TACT Controller WITH ROTARY PLATEN
SPECIFICATIONS
CLAMP UNIT
Clamp force: 132 U.S. Tons
Clamping stroke 450 mm (17.72")
Min mold thickness 170 mm (6.70")
Max daylight opening 620 mm (24.41")
Tie Bar clearance (HxV): 660 mm x 250 mm (25.99" x 9.85")
Die plate dim (HxV) stationary platen 800 mm x 480 mm (31.50" x 18.90")
Ejector stroke: 100 mm (3.93")
Max mold weight (movable side) kg 200 + 200
9A-9A INJECTION UNIT
Primary Side (Operator) Secondary Side (Non-Operator)
Screw diameter 36 mm (1.42"-C) 28mm (1.11-A)
Shot size: 3.82 oz. G.P.P.S. 2.31 oz G.P.P.S
Injection Pressure: 21,401 PSI 35,407 PSI
Screw speed: 0-130 RPM Constant Torque
130-170 RPM Variable Torque
ELECTRICAL UNIT
Pump motor kW: 18.5 (25 HP)
Primary & Heater voltage /phase/cycle: 380 Volts rewound to 575 volts
Control circuit: 24 volt DC
GENERAL
Hydraulic oil requirement: 425 litres
* Oil can be supplied by En-Plas at an additional charge
140ton Nissei FN3000 (1999)
SOLD !
SOLD !
ONLY USED YEAR 1999 NISSEI MODEL FN3000/140-36A INJECTION MOULDING MACHINE WITH 9300T Controller
SPECIFICATIONS
CLAMP UNIT
Mold clamping force: 154 U.S. Tons
Mold clamping stroke 600 mm (23.62)
Minimum mold thickness 250 mm (9.84)
Maximum daylight opening 850 mm (33.46)
Clearance between tie bars (HxV) 480 mm x 480 mm (18.90 x 18.90)
Die plate dimensions (HxV) 700 mm x 700 mm (27.56 x 27.56)
Ejector stroke 90 mm (3.54)
INJECTION UNIT
Shot size: 14.83 oz. G.P.P.S. (C)
Injection Pressure: 19410 PSI
Screw diameter: 2.2" (56mm)
Screw speed: 0-200 RPM Constant torque
200-240 RPM Variable torque
ELECTRICAL UNIT
Pump motor kW: 30
Primary voltage/phase/cycle: 575/3/60
Heater voltage/phase/cycle: 230/3/60
Control circuit: 24 volt DC
NOTE: Heater voltage requires separate 230 volt supply
*Transformer can be supplied by En-Plas for an additional charge
GENERAL
Hydraulic oil quantity requirements: 515 litres
*Oil can be supplied by En-Plas for an additional charge
MACHINE EQUIPPED WITH:
1. Dual core pull & Single Pneumatic Core Pull
2. Cycle counter
3. Centralized manual lubrication system
4. Screw cold start preventing circuit
5. Hydraulic oil temperature upper and lower limit warnings
6. Water saver valve
7. Used Mounting pads
8. Mould clamps
9. Air blow off circuit
10. Machine colour Nissei Green
150ton Nissei TD150 Vertical Rotary (1989)
ONE USED 1989 NISSEI MODEL TD150R25ASE VERTICAL INJECTION MOULDING MACHINE, PARTING INJECTION (TURNTABLE TYPE) With Light Curtain & in great condition - equipped 8000F Controller
SPECIFICATIONS
CLAMP UNIT
Clamp force: 165 U.S. Tons
Distance between tie bars ( HxV) 47.04" x 9.25"
Maximum clamp stroke: 13.77"
Mould shut height: 9.84"
Maximum daylight: 23.62"
Hydraulic ejector stroke: 3.94"
Turntable dimension 47.24"
INJECTION UNIT
Screw diameter: 45 mm (1.77")
Shot size: 8.5 oz. G.P.P.S.
Injection Pressure: 25170 PSI
Screw speed: 0-170 RPM (Low torque)
0-145
ELECTRICAL UNIT
Primary voltage /phase/cycle: 460/3/60*
Heater voltage/phase/cycle: 230/3/60
Control circuit: 24 volt DC
NOTE: Heater voltage requires separate 230 volt supply
GENERAL
Hydraulic oil quantity requirement: 192 U.S. gallons
160ton Nissei FS160S36ASE (1994)
new arrival
photo to come
(1) ONLY 1994 NISSEI MODEL FS160S36ASE INJECTION MOULDING MACHINE equipped with 9000F Controller
SPECIFICATIONS
CLAMP UNIT
Clamp force: 177 U.S. Tons
Distance Between Tie Bars (HxV): 18.2" x 18.2"
Platen size (HxV): 27" x 27"
Maximum clamp stroke: 18.5"
Mould shutheight: 7.9" to 16.1"
Maximum daylight: 34.6"
Hydraulic ejector stroke: 3.9"
INJECTION UNIT
Shot size: 14.8 oz. G.P.P.S. (C)
Injection Pressure: 19410 PSI
Screw diameter: 2.21"
Screw speed: 0-185 RPM (low torque)
0-145 RPM (high torque)
ELECTRICAL UNIT
Pump motor: 30 HP
Primary voltage /phase/cycle: 575/3/60
Heater voltage/phase/cycle: 230/3/60
Control circuit: 24 volt DC
NOTE: Heater voltage requires separate 230 volt supply
GENERAL
Machine weight: 7.2 U.S. Tons
Hydraulic oil quantity requirements: 151 gallons
180ton Nissei FN4000 (Yr 2000)
New Arrival!
SPECIFICATIONS
CLAMP UNIT
Mold clamping force: 196 U.S. Tons
Mold clamping stroke 700 mm (27.56)
Minimum mold thickness 250 mm (9.84)
Maximum daylight opening 950 mm (37.40)
Clearance between tie bars (HxV) 530 mm x 530 mm (20.87 x 20.87)
Die plate dimensions (HxV) 770 mm x 770 mm (30.31 x 30.31)
Ejector stroke 110 mm (4.33)
INJECTION UNIT
Screw diameter: 22mm
Shot size: 30grams
180ton Nissei FN4000 (2 x 1997)
2 Available - Both are New arrivals!!
Two USED 1997 NISSEI MODEL FN4000/180-36A INJECTION MOLDING MACHINE WITH 9000F Controller
SPECIFICATIONS
Shot: 21.40 oz
Tie Bar: 20.86 x 20.86
Platen: 30.31 x 30.31
Volts: 575 volts
Injection pressure 18,130 psi
Ejector stroke: 4.33
Used Equipment may have had modifications made to them that En-Plas Inc. is unaware of and take no responsibility for.
Specifications listed on our used equipment pages may differ from actual specifications on the equipment and are meant solely as a guideline.
|
