(416) 286-3030 blemieux@en-plasinc.com

Used 1450ton Nissei FV9400 (2004)

Only 2004 En-Plas Nissei Model FV9400/700L Injection Molding Machine with 24,500 hours 

With NC9300T Controller

With dual core pull

With dual air blow off circuit



Clamp force:                                                        1437 U.S. Tons

Mold clamping stroke                                          1300 mm (51.18”)

Mold thickness (min-max)                                   700 mm – 1250 mm (27.56” – 49.21”)

Maximum daylight opening                                 2560 mm (100.79”)

Clearance between tie bar (HxV)                        1450 mm x 1450 mm (57.09” x 57.09”)

Die plate dimensions (HxV)                                2020 mm x 2020 mm (79.53” x 79.53”)

Ejector stroke:                                                      280 mm (11.02″)


Screw diameter:                                                   135 mm (5.31″-C)

Shot size:                                                             297.10 oz G.P.P.S.

Injection Pressure:                                               19268 PSI

Screw speed:                                                        0-90 Constant torque

90 -115 Variable torque


Pump motor kw:                                                  55+75

Primary & heater voltage /phase/cycle:                575/230

Control circuit:                                                     24 volt DC

NOTE:  Heater voltage requires separate 230 volt supply

Transformer can be supplied by En-Plas for an additional charge

Hydraulic oil quantity                                          2400 litres (not included)


  1. Dual core pull
  2. Dual air blow
  3. Incoe Filter
  4. Cycle counter
  5. Centralized manual lubrication system
  6. Screw cold start preventing circuit
  7. Hydraulic oil temperature upper and lower limit warnings
  8. Water saver valve
  9. Machine wedgemounts
  10. Hopper magnet
  11. Mould clamps
  12. Machine colour Nissei green


Electronic controller with 6 speeds/3 holding pressure and 3 limit pressure profiling, shot discrimination and mold open/close linear encoders, colour screen and graphics and 1 floppy disk


High resolution colour 10.4″ touch flat screen.

30 mold storage in machine with removable disk drive to store up to 100 mold set-ups with 1 floppy disk.

Input/output analog displayed with explicit error messages.

RS232 port for printer

PID Control for barrel and oil with auto tuning on nozzle

Proportional control of the pump for all functions of the machine

Linear encoder for measurement of clamp, injection, ejection position

Optically isolated control system (Protection from electrical noise).

Real time graphics for injection functions.

Auto purging

6 step injection speed profiling.

6 step injection pressure profiling (3) fill, (3) hold.

Sprue break

Digital back pressure

2 speeds for plasticizing

3 mold opening and closing speeds plus 2 stage high pressure clamp.

Multi-stage hydraulic ejector control

Set value graphics for profiles for injection.

Interlock for part detection (not including sensor).

Core pull control software.

Graphic and alpha-numeric printing capability

Injection boost to hold switch over by time, position, hydraulic pressure or cavity sensor (individually or in combination)

Air blow software control

Real time clock

Cycle time monitoring and analysis

Interface for standard plant monitoring systems.

History reporting of machine cycle conditions and set-up changes

Quick machine set-up via a single page

Forced reject count.

Clamp retry up to 2 times.

Digital display of screw position, ejection and clamp with bar display of current position

Standard graph display for injection profile

Monitor tolerance window can be assigned for reject outputs.

Out of 17 processing variables, 8 can be recorded and 4 can be selected and displayed.

Graphic printouts can be generated.  Average and standard deviations are calculated.

Printer not included.

SPC option

Standby temperature program so when machine goes into alarm temperature drops to standby

(selectable for on/off).

High/low oil temperature alarm with solenoid control of water to maintain set temperature

Emergency temperature off for lights out operation selectable on/off


Total run time.

Grand total shot display.

Calendar function to turn barrel heat on automatically with option to add dryer, mold temp controller and spare

Unique machine identification through the controller Alpha numeric characters

Ejector backward confirmation by position through front screen

Mould ejector plate backward confirmation input software included (hardware extra)

Used Equipment may have had modifications made to them that En-Plas Inc. is unaware of and take no responsibility for. Specifications listed on our used equipment pages may differ from actual specifications on the equipment and are meant solely as a guideline.