(416) 286-3030 blemieux@en-plasinc.com

Used 180ton Nissei FN4000 Molding Machines

Used 1999 Nissei (FN180) FN4000 – 36A Injection Unit 180ton Molding Machine with 9300T controls

3 x Used 1999 Nissei (FN180) FN4000 – 36A Injection Unit 180ton Molding Machines all equipped with 9300T controls

COMING SOON

3 Available – one machine has a modified barrel and screw able to accommodate an 850 gram shot size.

Nissei FN Series

Please contact blemieux@en-plasinc.com for more details.

SPECIFICATIONS

CLAMP UNIT

Mold clamping force:                                          196 U.S. Tons

Mold clamping stroke                                          700 mm (27.56”)

Minimum mold thickness                                    250 mm (9.84”)

Maximum daylight opening                                 950 mm (37.40”)

Clearance between tie bars (HxV)                       530 mm x 530 mm (20.87” x 20.87”)

Die plate dimensions (HxV)                                770 mm x 770 mm (30.31” x 30.31”)

Ejector stroke                                                       110 mm (4.33”)

INJECTION UNIT

Screw diameter:                                                   56 mm (2.2″-C)

Shot size:                                                             14.8 oz. GPPS.

Injection Pressure:                                               19410 PSI

Screw speed:                                                        0-200 RPM high torque

200-240 RPM low torque

ELECTRICAL UNIT

Pump motor:                                                        40 HP

Motor & heater Voltage/phase/cycle:                  460/3/60** rewound to 575/230 volts

Control circuit:                                                     24 volt DC

Transformer can be supplied by En-Plas at an additional charge

GENERAL

Hydraulic oil quantity requirements:       700 litres (not included)

* Oil can be supplied by En-Plas at an additional charge

MACHINES WITH TOP OF THE LINE NC9300TCONTROLLER

Electronic controller with 6 speeds/3 holding pressures and 3 limit pressure profiling, shot discrimination and mold open/close linear encoders, colour screen and graphics, and 1 floppy disk

Including:    

High resolution colour 10.4″ touch flat screen.

30 mold storage in machine with removable disk drive to store up to 100 mold set-ups with 1 floppy disk.

Input/output analog displayed with explicit error messages.

RS232 port for printer

PID Control for barrel and oil with auto tuning on nozzle

Proportional control of the pump for all functions of the machine

Linear encoder for measurement of clamp, injection, ejection position

Optically isolated control system (Protection from electrical noise).

Real time graphics for injection functions.

Auto purging

6 step injection speed profiling.

6 step injection pressure profiling (3) fill, (3) hold.

Sprue break

Digital back pressure

2 speeds for plasticizing

3 mold opening and closing speeds plus 2 stage high pressure clamp.

Multi-stage hydraulic ejector control

Set value graphics for profiles for injection.

Interlock for part detection (not including sensor).

Core pull control software.

Graphic and alpha-numeric printing capability

Injection boost to hold switch over by time, position, hydraulic pressure or cavity sensor (individually or in combination)

Air blow software control

Real time clock

Cycle time monitoring and analysis

Interface for standard plant monitoring systems.

History reporting of machine cycle conditions and set-up changes

Quick machine set-up via a single page

Forced reject count.

Clamp retry up to 2 times.

Digital display of screw position, ejection and clamp with bar display of current position

Standard graph display for injection profile

Monitor tolerance window can be assigned for reject outputs.

Out of 17 processing variables, 8 can be recorded and 4 can be selected and displayed.

Graphic printouts can be generated.  Average and standard deviations are calculated.  Printer

not included.

SPC option

Standby temperature program so when machine goes into alarm temperature drops to standby

(selectable for on/off).

High/low oil temperature alarm with solenoid control of water to maintain set temperature

Emergency temperature off for lights out operation selectable on/off

Calculator

Total run time.

Grand total shot display.

Calendar function to turn barrel heat on automatically with option to add dryer, mold temp controller and spare

Unique machine identification through the controller Alpha numeric characters

Ejector backward confirmation by position through front screen

Mould ejector plate backward confirmation input software included (hardware extra)

 

 

MACHINE EQUIPPED WITH:

 

  1. Cycle counter
  2. Screw cold start preventing circuit
  3. Hydraulic oil temperature upper and lower limit warnings
  4. Used mounting pads
  5. Machine colour Nissei green
Used Equipment may have had modifications made to them that En-Plas Inc. is unaware of and take no responsibility for. Specifications listed on our used equipment pages may differ from actual specifications on the equipment and are meant solely as a guideline.